| Last additions - 1/4 Scale 50T |
489 viewsFeb 23, 2010
|
|
501 viewsFeb 23, 2010
|
|
464 viewsFeb 23, 2010
|
|
499 viewsFeb 23, 2010
|
|
498 viewsFeb 23, 2010
|
|
512 viewsFeb 23, 2010
|
|
497 viewsFeb 23, 2010
|
|
465 viewsFeb 23, 2010
|
|
491 viewsFeb 23, 2010
|
|
905 viewsOil pan from frontMay 28, 2007
|
|
803 viewsOil pan from frontMay 28, 2007
|
|
876 viewsOil pan from rearMay 28, 2007
|
|
767 viewsCam Gear CoversMay 24, 2007
|
|
765 viewsCam Gear CoversMay 24, 2007
|
|
644 viewsDistributor partsMay 19, 2007
|
|
818 viewsDistributors installedMay 19, 2007
|
|
854 viewsMiniature spark plugsApr 22, 2007
|
|
838 viewsSpark plugs Apr 22, 2007
|
|
897 viewsCrankcase ventsApr 12, 2007
|
|
799 viewsCrankcase vents installed. All four are fully functionalApr 12, 2007
|
|
927 viewsFlywheelMar 19, 2007
|
|
850 viewsCarb adapter plate with Walbro carbMar 04, 2007
|
|
978 viewsCarb adapter plate with Walbro carbMar 04, 2007
|
|
875 viewsCompressor dummy unitMar 01, 2007
|
|
938 viewsCompressor (blower here in the states) installed. Dummy unit for now until i learn how to cut the vanes.Mar 01, 2007
|
|
800 viewsIntake manifold rear sectionFeb 02, 2007
|
|
857 viewsIntake manifold rear section installedFeb 02, 2007
|
|
874 viewsIntake manifold front sectionFeb 02, 2007
|
|
949 viewsCompleted Intake ManifoldFeb 02, 2007
|
|
886 viewsIntake manifold rear sectionFeb 02, 2007
|
|
1100 viewsRotating AssemblyJan 21, 2007
|
|
907 viewsPistonsJan 21, 2007
|
|
887 viewsTiming CoverJan 20, 2007
|
|
1129 viewsTiming cover with belt installedJan 20, 2007
|
|
924 viewsConnecting RodsDec 31, 2006
|
|
1026 viewsConnecting RodsDec 31, 2006
|
|
926 viewsHead fabrication finished and assembledDec 21, 2006
|
|
889 viewsIntake and exhaust valves with spring keepersDec 15, 2006
|
|
1005 viewsValves InstalledDec 15, 2006
|
|
1110 viewsValves installedDec 15, 2006
|
|
760 viewsValve guides installedNov 29, 2006
|
|
836 viewsValve guides installedNov 29, 2006
|
|
817 viewsValve guide with prototype valveNov 26, 2006
|
|
833 viewsValve guides ready to be pressed into headNov 26, 2006
|
|
1129 viewsEverything together so far.Oct 14, 2006
|
|
1019 viewsBoth camshafts with bearings from the frontOct 14, 2006
|
|
846 viewsBoth camshafts with bearings from the topOct 14, 2006
|
|
1048 viewsFinished cam sitting in roller bearings next to blank cam. After valve is adjusted, lift is .090Oct 05, 2006
|
|
1069 viewsMain caps are done and installedSep 02, 2006
|
|
1060 viewsCrankshaft installed and spinning freelySep 02, 2006
|
|
1403 viewsCrankshaft is 17 pieces and 17 bearings pressed togetherAug 31, 2006
|
|
1056 viewsRear View of crankshaft. Crank disks are beefed up to provide more rotating mass in hopes that the engine will idle better.Aug 31, 2006
|
|
1116 viewsCrankshaft installed in crankcase. All main and rod bearings are ball bearing.Aug 31, 2006
|
|
981 viewsHead, Cylinder, and crankcase sections starting to take shapeAug 31, 2006
|
|
1160 viewsExhaust system ready for paintAug 31, 2006
|
|
940 viewsCam boxs installed Aug 31, 2006
|
|
1038 viewsValve cover front viewAug 31, 2006
|
|
1044 viewsValve cover from the rear with cam bearing installedAug 31, 2006
|
|
1064 viewsCrankcase bottom Aug 31, 2006
|
|
1066 viewsCrankcase top not quite finishedAug 31, 2006
|
|
| 63 files on 2 page(s) |
 |
1 | |
|
