| Top rated - 1/4 Scale 50T |
896 viewsFlywheel
(15 votes)
|
|
789 viewsDistributors installed
(10 votes)
|
|
867 viewsCrankcase vents
(12 votes)
|
|
994 viewsConnecting Rods
(25 votes)
|
|
1039 viewsMain caps are done and installed
(28 votes)
|
|
847 viewsIntake manifold front section
(20 votes)
|
|
1025 viewsCrankcase bottom
(27 votes)
|
|
1010 viewsValve cover front view
(24 votes)
|
|
1015 viewsValve cover from the rear with cam bearing installed
(26 votes)
|
|
1038 viewsCrankcase top not quite finished
(26 votes)
|
|
875 viewsOil pan from front
(9 votes)
|
|
767 viewsOil pan from front
(9 votes)
|
|
733 viewsCam Gear Covers
(9 votes)
|
|
731 viewsCam Gear Covers
(9 votes)
|
|
937 viewsCarb adapter plate with Walbro carb
(25 votes)
|
|
986 viewsBoth camshafts with bearings from the front
(25 votes)
|
|
803 viewsSpark plugs
(11 votes)
|
|
1129 viewsExhaust system ready for paint
(26 votes)
|
|
919 viewsCompleted Intake Manifold
(23 votes)
|
|
1099 viewsEverything together so far.
(26 votes)
|
|
1016 viewsFinished cam sitting in roller bearings next to blank cam. After valve is adjusted, lift is .090
(26 votes)
|
|
1098 viewsTiming cover with belt installed
(24 votes)
|
|
769 viewsIntake manifold rear section
(12 votes)
|
|
845 viewsOil pan from rear
(10 votes)
|
|
825 viewsMiniature spark plugs
(10 votes)
|
|
764 viewsCrankcase vents installed. All four are fully functional
(10 votes)
|
|
907 viewsCompressor (blower here in the states) installed. Dummy unit for now until i learn how to cut the vanes.
(22 votes)
|
|
874 viewsPistons
(22 votes)
|
|
1080 viewsValves installed
(25 votes)
|
|
813 viewsCarb adapter plate with Walbro carb
(12 votes)
|
|
1371 viewsCrankshaft is 17 pieces and 17 bearings pressed together
(28 votes)
|
|
1027 viewsCrankshaft installed and spinning freely
(25 votes)
|
|
898 viewsHead fabrication finished and assembled
(23 votes)
|
|
813 viewsBoth camshafts with bearings from the top
(21 votes)
|
|
862 viewsIntake manifold rear section
(21 votes)
|
|
976 viewsValves Installed
(24 votes)
|
|
905 viewsCam boxs installed
(24 votes)
|
|
844 viewsCompressor dummy unit
(19 votes)
|
|
996 viewsTop of head showing valve guide and sparkplug holes
(25 votes)
|
|
887 viewsConnecting Rods
(23 votes)
|
|
799 viewsValve guides ready to be pressed into head
(21 votes)
|
|
928 viewsCylinder section bottom
(24 votes)
|
|
787 viewsValve guide with prototype valve
(19 votes)
|
|
950 viewsHead, Cylinder, and crankcase sections starting to take shape
(24 votes)
|
|
921 viewsBottom of head showing combustion chambers,intake and exhaust ports
(25 votes)
|
|
823 viewsIntake manifold rear section installed
(18 votes)
|
|
735 viewsValve guides installed
(18 votes)
|
|
1020 viewsRear View of crankshaft. Crank disks are beefed up to provide more rotating mass in hopes that the engine will idle better.
(22 votes)
|
|
1070 viewsRotating Assembly
(23 votes)
|
|
1091 viewsCrankshaft installed in crankcase. All main and rod bearings are ball bearing.
(25 votes)
|
|
849 viewsTiming Cover
(22 votes)
|
|
798 viewsValve guides installed
(22 votes)
|
|
863 viewsIntake and exhaust valves with spring keepers
(23 votes)
|
|
610 viewsDistributor parts
(5 votes)
|
|
464 views
(1 votes)
|
|
464 views
(1 votes)
|
|
429 views
(1 votes)
|
|
468 views
(1 votes)
|
|
467 views
(1 votes)
|
|
481 views
(1 votes)
|
|
| 63 files on 2 page(s) |
 |
1 | |
|
