Top rated - stevehuckss396's Gallery |
488 viewsDistributors installed (7 votes)
|
|
471 views (11 votes)
|
|
564 viewsFlywheel (12 votes)
|
|
537 viewsCrankcase vents (9 votes)
|
|
404 viewsFailed 4 cylinder (3 votes)
|
|
361 viewsFuture V8 Co2 motor (2 votes)
|
|
479 views (8 votes)
|
|
463 views (7 votes)
|
|
560 viewsOil pan from front (6 votes)
|
|
465 viewsOil pan from front (6 votes)
|
|
444 viewsCam Gear Covers (6 votes)
|
|
453 viewsCam Gear Covers (6 votes)
|
|
308 viewsCompleted cam box (6 votes)
|
|
318 views (5 votes)
|
|
700 viewsConnecting Rods (22 votes)
|
|
544 viewsIntake manifold front section (17 votes)
|
|
730 viewsMain caps are done and installed (25 votes)
|
|
523 viewsSpark plugs (8 votes)
|
|
287 viewsCambox ready for assembly (4 votes)
|
|
700 viewsValve cover front view (21 votes)
|
|
532 viewsOil pan from rear (7 votes)
|
|
516 viewsMiniature spark plugs (7 votes)
|
|
471 viewsCrankcase vents installed. All four are fully functional (7 votes)
|
|
715 viewsCrankcase bottom (24 votes)
|
|
494 viewsIntake manifold rear section (9 votes)
|
|
716 viewsValve cover from the rear with cam bearing installed (23 votes)
|
|
714 viewsCrankcase top not quite finished (23 votes)
|
|
653 viewsCarb adapter plate with Walbro carb (22 votes)
|
|
679 viewsBoth camshafts with bearings from the front (22 votes)
|
|
818 viewsExhaust system ready for paint (23 votes)
|
|
612 viewsCompleted Intake Manifold (20 votes)
|
|
823 viewsTiming cover with belt installed (21 votes)
|
|
797 viewsEverything together so far. (23 votes)
|
|
717 viewsFinished cam sitting in roller bearings next to blank cam. After valve is adjusted, lift is .090 (23 votes)
|
|
516 viewsCarb adapter plate with Walbro carb (9 votes)
|
|
598 viewsCompressor (blower here in the states) installed. Dummy unit for now until i learn how to cut the vanes. (19 votes)
|
|
587 viewsPistons (19 votes)
|
|
784 viewsValves installed (22 votes)
|
|
182 viewsShortblock parts ready fpr assembly (2 votes)
|
|
1060 viewsCrankshaft is 17 pieces and 17 bearings pressed together (25 votes)
|
|
726 viewsCrankshaft installed and spinning freely (22 votes)
|
|
610 viewsHead fabrication finished and assembled (20 votes)
|
|
523 viewsBoth camshafts with bearings from the top (18 votes)
|
|
572 viewsIntake manifold rear section (18 votes)
|
|
546 viewsCompressor dummy unit (16 votes)
|
|
700 viewsValves Installed (21 votes)
|
|
615 viewsCam boxs installed (21 votes)
|
|
686 viewsTop of head showing valve guide and sparkplug holes (22 votes)
|
|
593 viewsConnecting Rods (20 votes)
|
|
511 viewsValve guides ready to be pressed into head (18 votes)
|
|
629 viewsCylinder section bottom (21 votes)
|
|
499 viewsValve guide with prototype valve (16 votes)
|
|
217 views (3 votes)
|
|
228 viewsFinished Rotating assembly (3 votes)
|
|
230 viewsShortblock with polished cylinder liners (3 votes)
|
|
631 viewsHead, Cylinder, and crankcase sections starting to take shape (21 votes)
|
|
524 viewsIntake manifold rear section installed (15 votes)
|
|
450 viewsValve guides installed (15 votes)
|
|
613 viewsBottom of head showing combustion chambers,intake and exhaust ports (22 votes)
|
|
710 viewsRear View of crankshaft. Crank disks are beefed up to provide more rotating mass in hopes that the engine will idle better. (19 votes)
|
|
88 files on 2 page(s) |
|
1 | |
|